Click logo to return to home page. ]

 
Home>Forums>Scale Cockpits and Pilots>Cane pilot seat Sopwith 1/4 scale weaving Search Within This Topic   
Post Reply   New Topic   
Forum Jump 5 Pages 1 2 3 4 5
] ] ]
]
Author / Post
Avatar User Offline ska2000
Basic Member
Basic Member
Joined: May/23/2008
National Flag of United States United States
Posts: 138
IP Logged
Posted: April/23/2019 at 12:13pm  Quote
 
Quote: ScaleAero
Looked for the 3D printed cane eat in RCSB with "0" result. Anyone recall
which thread it might have been in? Weaving would be great but I need a
few more than one or two for a Tri-motor. Will look at a couple of 3D sites
and post what I find.

Goodness. I scanned every page of the BE2C thread twice before I found it again. And it's on PAGE 1! LOL
Pictures of a partially 3D printed wicker pilot seat here  https://www.rcscalebuilder.com/forum/forum_posts.asp?TID=282 68&PN=1&TPN=1


__________________
Tom
Some assembly required
 
Back to Top  Printer Friendly Version  Profile  Search 
 
Avatar User Offline Teus
Lifetime Site Supporter
Lifetime Site Supporter
Dutch Dawn Patrol
Joined: December/09/2006
National Flag of Netherlands Netherlands
Posts: 3856
IP Logged
Posted: April/23/2019 at 12:29pm  Quote
 
There is one advertised on Vogelsangs website....   Click

__________________
Teus

Building board:
1/4 Fokker V.23

Flying:
1/4 Proctor Fokker E.III
1/3rd Fokker D-VII
1/3rd Nieuport-11
 
Back to Top  Printer Friendly Version  Profile  Search  Web 
 
Avatar User Offline Teus
Lifetime Site Supporter
Lifetime Site Supporter
Dutch Dawn Patrol
Joined: December/09/2006
National Flag of Netherlands Netherlands
Posts: 3856
IP Logged
Posted: April/23/2019 at 12:36pm  Quote
 
And here another beautiful and easy to do example of how Brian did it for his Be2c...... Click

__________________
Teus

Building board:
1/4 Fokker V.23

Flying:
1/4 Proctor Fokker E.III
1/3rd Fokker D-VII
1/3rd Nieuport-11
 
Back to Top  Printer Friendly Version  Profile  Search  Web 
 
Avatar User Online ScaleAero
Supporting Vendor
Supporting Vendor
Joined: September/09/2003
National Flag of United States United States
Posts: 9719
IP Logged
Posted: April/23/2019 at 12:55pm  Quote
 
Quote: ska2000
Quote: ScaleAero
Looked for the 3D printed cane eat in RCSB with "0" result. Anyone recall which thread it might have been in? Weaving would be great but I need a few more than one or two for a Tri-motor. Will look at a couple of 3D sites
and post what I find.
Goodness. I scanned every page of the BE2C thread twice before I found it again. And it's on PAGE 1! LOL Pictures of a partially 3D printed wicker pilot seat here  https://www.rcscalebuilder.com/forum/forum_posts.asp?TID=282 68&PN=1&TPN=1


Why is it I feel painfully inadequate after viewing that from top to bottom. Felt as if I was 
in the 1:1 factory... Like someone said in thread, is the thread host in the wrong site?
More than wonderful skill set Also, a complete absence of dust. Must have a Rumba in
the shop...or someone following around with a dust pan and broom.

__________________
Ed
http://www.flitemetal.com
http://www.mac-models.com
 
Back to Top  Printer Friendly Version  Profile  Search  Web 
 
Avatar User Offline ska2000
Basic Member
Basic Member
Joined: May/23/2008
National Flag of United States United States
Posts: 138
IP Logged
Posted: April/23/2019 at 1:00pm  Quote
 
Quote: ScaleAero
Why is it I feel painfully inadequate after viewing that from top to bottom. Felt as if I was 
in the 1:1 factory... Like someone said in thread, is the thread host in the wrong site?
More than wonderful skill set Also, a complete absence of dust. Must have a Rumba in
the shop...or someone following around with a dust pan and broom.

I feel your pain! LOL Amazing work. Some of these builds here are nothing short of awe inspiring. And the ingenuity! Just look at the result of this thread and how many ways guys have invented to replicate a wicker pilot seat. Bravo to these hyper-accomplished builders. Currently reading these threads is one of my chief forms of entertainment. Always amazed.


__________________
Tom
Some assembly required
 
Back to Top  Printer Friendly Version  Profile  Search 
 
Avatar User Offline shaas
Site Supporter
Site Supporter
Joined: September/23/2009
National Flag of United States United States
Posts: 6
IP Logged
Posted: April/23/2019 at 1:43pm  Quote
 
Dynamic Balsa has a 3D printed seat  

https://www.dbalsa.com/accessories/images/IMG_1600.JPG
www.dbalsa.com/accessories/scale-accessories.htm

 
Back to Top  Printer Friendly Version  Profile  Search 
 
Avatar User Online ScaleAero
Supporting Vendor
Supporting Vendor
Joined: September/09/2003
National Flag of United States United States
Posts: 9719
IP Logged
Posted: April/23/2019 at 1:52pm  Quote
 
That's the same as the BE2C seat... The issue is size. That is why I have looked
for an .stl with which to print in proper scale for a Ford Trimotor.

__________________
Ed
http://www.flitemetal.com
http://www.mac-models.com
 
Back to Top  Printer Friendly Version  Profile  Search  Web 
 
Avatar User Offline hammerd
Site Supporter
Site Supporter
Joined: July/22/2008
National Flag of United States United States
Posts: 943
IP Logged
Posted: April/23/2019 at 2:08pm  Quote
 
Ed, I meant to upload the file for my seat here already. I'll do that tonight.
 
Back to Top  Printer Friendly Version  Profile  Search 
 
]
] ]
Forum Jump 5 Pages 1 2 3 4 5

 

  Post Reply   New Topic   

] ] ]
]
   ]
Similar topics you might be interested in...
Pilot kit 1/4 scale Decathlon
Globe Swift 1/4 scale drawings
optimal radio setup for 1/4 scale warbird
BUSA Sopwith Pup 1/4 scale question
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot delete your posts in this forum
You cannot edit your posts in this forum
You cannot create polls in this forum
You cannot vote in polls in this forum
]
] ]

Home Icon Portal Home   Forum Icon Forum Home   Forum Icon Your Privacy

Copyright © 2003-2025, RCSCALEBUILDER.COM, All Rights Reserved